|
  |
 SLI lässt sich nicht aktivieren |
Shifty
Steuerzahler
Dabei seit: 14.07.2006
Beiträge: 225
|
|
Hab da was gefunden was dir u.U. weiterhelfen könnte:
r_multigpu [0,1] - This setting is the same as the 'Optimize for SLI' option in the in-game settings. As such, you should set it there, however check to make sure it is set appropriately for your system (i.e. 0 for single graphics card users, 1 for SLI users). Also make sure to check the r_gpysync value (See below) for optimal performance. Some single graphics card users note a performance improvement when setting this option to 1, however this may induce keyboard/mouse lag. There is further discussion of these settings in the Conclusion section of the guide.
r_gpuSync [0,1,2,3] - This setting determines the synchronization of the GPU (graphics processing unit) and CPU. The values for the various modes are 0 for Off, 1 for Beginning, 2 for beforePresent, and 3 for Adaptive. Importantly, this setting currently defaults to 3 for all users which is a conscious decision by Infinity Ward to balance performance and responsiveness. This is because if set to 0, you may gain performance however your control input (keyboard and/or mouse input) may become laggy as the CPU and GPU go slightly out of sync in places (See Conclusion section). If you are desparate for extra FPS, set this to 0, however if you notice mouse/keyboard lag even at 30+ FPS, then reset to the default value 3 (Adaptive) which keeps the CPU and GPU in sync.
Quelle: TweakGuides.com
__________________
- Cooler Master RC-690-KWN1-GP
- Intel Core2Quad Q9450, 12MB,LGA775, 64-bit
- XFX nForce 780i - 3-Way-SLI ATX
- XFX GeForce 8800GTX - 600M, 768MB DDR3 (2x , SLI-Mode)
- 4096MB PC2-6400 OCZ ReaperX HPC Enhanced Bandwith (CL4)
- Enermax PRO82+ 625W
|
|
|
|
|
|
|
Normalerweise geht es so:
COD2 starten, aber noch nicht zu einem Server connecten!
Dann die Settings für SLI vornehmen.
COD2 wieder schließen.
Nun müßten die Einstellungen gespeichert sein.
cu Mike
__________________
++++ To Yoda: Jedi-Meister bekommt Auris zugeschickt. Unmöglich nichts ist ++++ 
|
|
|
|
|
R.A.G.E
5-Minuten-Ei
Dabei seit: 13.04.2006
Beiträge: 12
|
|
Danke Shifty....mein Dank wird dir ewig nachschleichen:-)
einfach seta r_mulitgpu "1"
in die config schreiben dann gehts......
@Mike
das Problem war ja das ich es im Spiel eingestellt habe und wenn ich das Spiel neu gestartet war hat es sich wieder auf SLI Aus umgestellt
Trotzdem thanks
__________________
AMD Opteron 146@2950Mhz
DFI Lanparty Ut NF4 SLI-DR
Teamgroup Extreem 2GB Dual Channel Kit CL2,5 Command Rate 1T
Sapphire RAdeon 7950XTX Toxic
Plextor DVD Laufwerk mit festinstalliertem COD2 :D
|
|
|
|
|
R.A.G.E
5-Minuten-Ei
Dabei seit: 13.04.2006
Beiträge: 12
|
|
seta r_ multigpu "1"
wollt ich natürlich schreiben
__________________
AMD Opteron 146@2950Mhz
DFI Lanparty Ut NF4 SLI-DR
Teamgroup Extreem 2GB Dual Channel Kit CL2,5 Command Rate 1T
Sapphire RAdeon 7950XTX Toxic
Plextor DVD Laufwerk mit festinstalliertem COD2 :D
|
|
|
|
|
|
|
|
|
Impressum ||Datenschutzerklärung
|
Zitat:
